焊煙除塵設備在日產的運用中需求我們進行日常的保護，這樣才能確保設備正常的運轉。下面就帶大家了解下焊煙除塵設備日常保護的幾個關鍵。

The application of welding smoke and dust removal equipment in Nissan requires us to carry out daily protection in order to ensure the normal operation of the equipment. Below, we will take you to understand several key daily protection measures for welding smoke and dust removal equipment.

　　1、管理人員應熟悉除塵器的原理、性能、運用條件，并掌握調整和修理辦法。

1. Management personnel should be familiar with the principle, performance, and operating conditions of dust collectors, and master adjustment and repair methods.

　　2、定期測定工藝參數，如煙氣量、溫度、濃度等，發現異常，應查找原因并及時處理。

2. Regularly measure process parameters such as smoke volume, temperature, concentration, etc. If abnormalities are found, the cause should be identified and promptly addressed.

　　3、減速機、輸灰設備等機械運動部件應按規定注油和換油，發現有不正常現象應及時排除。

3. Mechanical moving parts such as reducers and ash conveying equipment should be lubricated and replaced according to regulations. Any abnormal phenomena should be promptly eliminated.

　　4、電磁脈沖閥如發生毛病，應及時地排除，如內部有雜質、水分，應進行清理，如膜片損壞應及時 換。

4. If the electromagnetic pulse valve malfunctions, it should be promptly eliminated. If there are impurities or moisture inside, it should be cleaned. If the diaphragm is damaged, it should be replaced in a timely manner.

　　5、停機時，不用堵截緊縮氣源，尤其在風機作業時， 向提高閥氣缸供給緊縮空氣，以確保提高閥處開啟狀況。

5. When shutting down, there is no need to block the compressed air source, especially during fan operation, to supply compressed air to the lifting valve cylinder to ensure the opening status of the lifting valve.

　　6、除塵器在正常作業時，排灰設備不能停止作業，否則，灰斗內很快會積滿粉塵致使溢入袋室，迫使除塵器停止作業。

6. When the dust collector is operating normally, the ash discharge equipment cannot stop working. Otherwise, the ash hopper will quickly accumulate dust and overflow into the bag room, forcing the dust collector to stop working.

　　7、開機時，應先接通緊縮空氣至儲氣罐，接通操控電源，發動排灰設備，假如體系中還有其它設備，應先發動下游設備。

7. When starting up, the compressed air should be connected to the air storage tank, the control power should be turned on, and the ash discharge equipment should be started. If there are other equipment in the system, the downstream equipment should be started first.

　　8、儲氣罐、氣源三聯件中的油水分離器應每班排污一次，一起油水分離器應每隔3～6月清洗一次，油霧器應常常查看存油狀況，及時加油。

8. The oil-water separator in the gas storage tank and gas source triple unit should be discharged once per shift, and the oil-water separator should be cleaned every 3-6 months. The oil mist collector should regularly check the oil storage status and add oil in a timely manner.

　　9、運用定時式清灰操控柜，應定期測定清灰周期是否準確，否則應進行調整。運用定阻式脈沖操控儀，應定期查看壓力開關的作業狀況，測壓口是否堵塞，并進行清理。

9. When using a timed ash cleaning control cabinet, the accuracy of the ash cleaning cycle should be regularly measured, otherwise adjustments should be made. When using a fixed resistance pulse controller, it is necessary to regularly check the operation status of the pressure switch, check if the pressure measuring port is blocked, and clean it.

　　10、停機時，在工藝體系停止之后，應保持除塵器和排風機持續作業一段時間，以除塵設備內的潮氣和粉塵， 注意的是，在除塵器停止作業時， 反復對除塵器進行清灰(可用手動清灰)，將除塵濾袋上的粉塵除掉，以訪受潮氣影響而糊袋子。

10. When shutting down, after the process system stops, the dust collector and exhaust fan should be kept operating continuously for a period of time to remove moisture and dust from the dust removal equipment. It is important to repeatedly clean the dust collector (manual cleaning can be used) when the dust collector stops working, remove the dust from the dust filter bag, and prevent the bag from being affected by moisture and sticking.

以上就是有關：多工位焊煙除塵設備 的介紹，想了解更多的內容請點擊：http://m.gtjjw.cn 我們將會全心全意為您提供滿分服務，歡迎您的來電！

The above is an introduction to multi station welding smoke and dust removal equipment. To learn more, please click: http://m.gtjjw.cn We will wholeheartedly provide you with full score service. Welcome to call us!

上一篇：自動式拋丸機的工作原理
下一篇：VOCs廢氣處理設備的使用壽命